TMW Off-Road
Factory UTV
Axia Alloys


Sport UTVs:
Polaris RZR XP 4 1000
Polaris RZR XP 1000
Arctic Cat Wildcat
Can-Am Maverick
Polaris RZR XP 900
Can-Am Commander
Yamaha Rhino
Kawasaki Teryx FI 4x4 Sport
Polaris RZR S


Product Review

Rhino Pedal System

Yamaha Rhino Pedal System
Rhino Pedal System from Desert Molding

The Hardware:

The slider part of the pedal assembly is made from a two component polyurethane. It's physical properties include high shore "D" hardness, high abrasion resistance and high heat resistance. The aluminum substrate is chemically treated prior to the molding process to create a bond between the aluminum and the polyurethane. Once molded the aluminum and polyurethane act as one to create a highly durable assembly.

The assembly also comes with all stainless mounting hardware and hinge.

Gas Pedal Installation:

1. Disconnect stock gas pedal return spring.

RhinoPedals-2.jpg (29954 bytes)

2. Remove throttle cable from bulkhead.

RhinoPedals-3.jpg (25611 bytes)   RhinoPedals-4.jpg (31454 bytes)

3. Mark line 1/2" down from top of stock gas pedal.

RhinoPedals-5.jpg (34812 bytes)   

4. Where hinge lays, grind down raised area on floor board so hinge lays flush.

RhinoPedals-8.jpg (34151 bytes)

5. Lay new pedal over stock gas pedal so that it is centered and the top of the new pedal rests 1/2" from the top of the stock pedal.

RhinoPedals-6.jpg (36277 bytes)

6. With hinge flat on the floor, mark location of hinge.

RhinoPedals-9.jpg (36507 bytes)   RhinoPedals-11.jpg (33404 bytes)

7. Remove hinge from pedal

8. Place hinge over pre-marked hinge location and mark hole locations

RhinoPedals-12.jpg (31228 bytes)

9. Inside hole (closest to tunnel) - drill 5/32" and clearance slightly. Install #10 sheet metal screw.

RhinoPedals-13.jpg (30391 bytes)

10. Outside hole - drill 7/32" hole through floor pan.  Install 10-32 machine screw, washer and nut.

RhinoPedals-14.jpg (32238 bytes)

11. Reinstall new pedal on hinge and tighten.

RhinoPedals-15.jpg (37043 bytes)

12. Reinstall stock throttle cable.

13. Reinstall stock gas pedal return spring.

14. Check pedal assembly for proper fit and function prior to operating vehicle.

15. Periodically check all mounting hardware.

16. Periodically check throttle cable for proper adjustment to make sure you are getting full throttle when pedal is to the floor.  This adjustment has nothing to do with the new pedal, but even a stock Rhino will need to be checked and adjusted.

Conclusions:

The gas pedal is much more comfortable and easy to use.  Regardless of foot position, you are able to apply proper amount of pressure to the pedal. We highly recommend this simple addition to your Yamaha Rhino.

Contact Info:

The Yamaha Rhino Desert Molding Pedal System can be purchased from PDS Fabrication:

Website: PDS Fabrication
Phone: 951-696-1650


Back to Product Reviews

Back to Sand Dune Guide


Long Travel:
Can-Am Commander Long Travel Kits
Kawasaki Teryx Long Travel Kits
Polaris RZR Long Travel Kits
Arctic Cat Prowler Long Travel Kits
Yamaha Rhino Long Travel Kits


Favorite Sites:
UTV Guide
SxSNews.com
Crowley Offroad
UTV News
Facebook
UTV Models



 

Dune News | Trip Reports  |  Advertise  | Contact Us

Worldwide Dunes  |  Closed Dunes

 

 

Copyright 2010 Crowley Offroad LLC. All rights reserved.
No images or content represented on this web site may be copied, stored, manipulated, published,
sold or reproduced in whole or in part without express written permission.

OpenCube AJAX Components


hits counter